- #Kerosun monitor 30 install#
- #Kerosun monitor 30 manual#
- #Kerosun monitor 30 series#
Replace the cabinet on the fuel tank and reattach.Trim any ragged edges that appear at the top of the wick.Turn the knob clockwise and counterclockwise a few times to make sure the mechanism is functioning smoothly. Position the adjuster knob to the front of the heater and tighten the wing nuts onto the retainers.Replace the wick and adjuster mechanism in the fuel tank, making sure the wick fits evenly in place.Slide the rubber packing over the wick and allow the tails of the wick to drop down.Check the height of the wick, then press it against the teeth inside the adjuster to obtain a firm grip.Turn the wick adjuster clockwise as far as it will go.The red line on the outside of the wick should match the bottom edge of the adjuster. Fold the new wick and slide it into the adjuster.
#Kerosun monitor 30 install#
To install the new wick, turn the wick adjuster counterclockwise as far as it will go. Remove the wick adjuster mechanism by loosening the wing nuts until you can turn the retainers that hold it in place. Remove the screws at the side of the extinguisher assembly and lift it out. Slide the electrical wire connectors off the battery case. Remove the safety shutoff reset lever by pulling it straight out of the cabinet. Open the front grille and remove the chimney. For many models simply hit the heater body with your hand. Follow the manufacturer’s recommendation for activating the automatic shutoff. Drain or burn off all the fuel in the tank and allow the heater to cool completely. Replace the kerosene heater wick on most kerosene heaters: Vacuum away any residue or soot from the burner area. Remove any remaining ash with an old toothbrush. Allow the wick to burn until the fire is completely out and no carbon remains on the wick. Be sure the chimney is properly centered. Light it with a match if you cannot light it automatically. Turn the wick to its highest position. Remove all the fuel from the tank or wait until the tank is empty. Recycle dirty fuel by calling your local hazardous waste recycler for instructions.īurn off a kerosene heater’s carbonized wick to restore softness: 
Fill the tank with clean, pure K-1 low-sulfur kerosene or as recommended by the manufacturer.Drain the cartridge tank and the burner tank, wiping up any spilled kerosene.Remove the wick and dry it on absorbent paper.What Are the Steps to Kerosene Heater Repair? Eliminate impurities in kerosene:
#Kerosun monitor 30 manual#
Models differ and the owner’s manual has the specific information on Your owner’s manual handy and refer to it often because kerosene heater The tools you will need to fix a kerosene heater include these: You can find common replacement parts for kerosene heaters at fireplace stores, larger hardware stores, and directly from the manufacturer. What Do I Need for Kerosene Heater Repair?
#Kerosun monitor 30 series#
If the wick has worn out or become damaged, you can easily replace it with a series of quick and simple steps (see below). If the wick adjuster sticks, clean the system of impure kerosene (see below) and burn the wick clean of carbon or tar (see below), or trim away the dirty part of the wick. If the wick burns too quickly, clean the system of impure kerosene (see below). If the flame smokes or causes odor, lower the wick to reduce the flame, move the heater out of direct drafts, make sure the chimney is level, burn the wick clean of carbon or tar (see below), trim away the dirty part of the wick, or clean the system of impure kerosene (see below). If the flame flickers or dies, remove any water in the system (see below), burn clean a wick covered with carbon or tar (see below), or trim away the dirty part of the wick. If the heater won’t light, fill an empty fuel tank, eliminate impurities in the system (see below), check the igniter batteries, adjust the wick until the igniter contacts the top of the wick, and replace a faulty igniter (see below). Components of a typical convection kerosene heater.
0 kommentar(er)
